Sage-Tips

How do you fix a gas fireplace that keeps going out?

Easy DIY Fix: Gas Fireplace Won’t Stay Lit

1. Before You Begin: Is Your Pilot Light Lit Inside Fireplace?
2. The Fix: Pilot Light to Gas Fireplace Won’t Stay Lit.
3. Check Your Thermopile Output with the TH/TP Contacts.
4. Don’t Replace Your Thermopile or Thermocouple Right Away.
5. Cleaning the Thermopile.
6. Re-test the Cleaned Thermopile.

Why is my gas fireplace flickering?

Flame flickers or spits – A draft in the room can cause your flame to flicker. Spitting is often caused by a dirty gas orifice or tube. These can be cleaned with a stiff wire, but you’ll need to remove the pilot light assembly to do so.

Why did my gas fireplace turn on by itself?

What is the mystery behind why the gas fireplace turns on by itself? The main reason behind this is always the faulty parts. You see, the damaged thermocouple or remote might be the reason. Other times, some wiring issues or switch problem arises that causes the fireplace to light on its own.

How long do gas fireplaces last?

How Long Can a Gas Fireplace Last? Generally speaking, you can get a good ten to fifteen years of use before you need to replace your gas fireplace.

Do gas fireplaces shut off automatically?

Nearly every new gas fireplace comes equipped with safety features such as a 100\% fail-safe shut-off valve. If the pilot flame goes out, the gas flow will automatically turn off. This device automatically shuts the gas off if the temperature in the fireplace gets too cold or if too much carbon monoxide builds up.

Does a gas fireplace have a thermostat?

Many gas fireplaces also offer automatic thermostat controls, which help keep the room temperature at a more constant level by automatically adjusting the firing rate.

How do you clean a thermocouple on a gas fireplace?

How to Clean the Thermocouple in a Gas Fireplace

1. Turn off the fireplace gas valve and remove the front panel from the fireplace.
2. Find the thermocouple, which is located next to the pilot light and looks like a small straight pipe.
3. Use a can of compressed air to gently blow away any dust and dirt from the thermocouple.

What can go wrong with a gas fireplace?

Top 10 Problems With Gas Fireplaces

• #1 Lack of maintenance, cleaning, and inspections.
• #2 Fear of gas.
• #3 The smell of burning gas.
• #4 Burner failure from pet hair and dander.
• #5 Dead batteries.
• #6 Raw gas/gas leak.
• #7 Cloudy/white glass.
• #8 The gas has not been turned on.

How much does it cost to fix gas fireplace?

Gas Fireplace Repair Cost Repairing a gas fireplace typically costs between $175 and $917. Most homeowners pay between $160 to $820 for general fireplace repairs (regardless of fuel type) but prices could range from $90 all the way to $2,000 on the high end.

Why does my gas fire place keep going out?

Gas pressure. If your gas pressure is not set correctly,your fireplace will not work as it should.

Faulty gas valve. Gas valve failure is rare,but when it happens,it is a fire hazard,and the valve should be replaced by a trained professional.

Moisture in the gas line. This is also rare.

Blocked burner ports.

How to start a gas fireplace?

– Turn the knob from the “Off” to the “Pilot” position. – Push in the pilot knob, which manually sends gas into the system. – Push the igniter button once every second until it lights. Depending on how long it’s been since the gas fireplace was last used, ignition may take multiple attempts. – After the pilot lights, keep the pilot button held down about 15 to 30 seconds to warm up the thermocouple and ensure that the flame stays lit. – Release the pilot knob. If the flame stays lit, rotate the knob to the “On” position. – Adjust the flame to the desired position with the “High/Low” switch or knob, if available. – Reattach the cover or screen over the control panel.

How to turn off a gas fireplace?

If the system involves opening a gas valve with a fireplace key,use a long match or lighter.

If you’re using a fireplace key and your fireplace has a front cover,remove it completely and set it aside to access the burner.

If the control panel’s pilot knob is not already in “Off” position,turn it off. Wait about five minutes to allow lingering or excess gas to clear out.

How do you turn off a gas fireplace?

Turn off the gas and look at the logs or under the logs to see where the gas comes out. Now turn the gas back on with the gas key and hold a long match or fireplace lighter there. If it doesn’t light right away the gas may be turned off at the source. You will need to get the fireplace and gas line inspected.